Christie CP2230 Instrukcja Konfiguracji

CP2230Setup Guide020-100515-04

CP2230 Setup Guide 1-1020-100515-04 Rev. 1 (05-2014)1 IntroductionThis manual is intended for professionally trained operators of Christie high-bright

1-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Introductiongovernment guidelines for your area. 2) Be aware that some medications are known toinc

IntroductionCP2230 Setup Guide 1-3020-100515-04 Rev. 1 (05-2014)turns OFF turning the cinema projector off, disconnecting it from a power source, ando

CP2230 Setup Guide 2-1020-100515-04 Rev. 1 (05-2014)2 Installation and SetupThis section provides information and procedures for positioning and insta

2-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup2.3 Cinema Projector ComponentsAir Filter Cover and Air FilterThe air filter

Installation and SetupCP2230 Setup Guide 2-3020-100515-04 Rev. 1 (05-2014)LED Status IndicatorsProvide information about the status of the cinema proj

2-4 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup• Reset: This button is slightly recessed into the faceplate to prevent acci

Installation and SetupCP2230 Setup Guide 2-5020-100515-04 Rev. 1 (05-2014)2.4 Installation Safety and Warning Guidelines • QUALIFIED TECHNICIAN REQUIR

2-6 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setupcombines with a very wide screen, you may have to forfeit some aim and stay

Installation and SetupCP2230 Setup Guide 2-7020-100515-04 Rev. 1 (05-2014) c. Insert the LPS support into the rack stand and align the pins with the h

2-8 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup2.6 Secure the Cinema Projector Use of the cinema projector’s rear safety st

Installation and SetupCP2230 Setup Guide 2-9020-100515-04 Rev. 1 (05-2014)2.8 Install the Touch Panel Controller (TPC)1. Loosen the mounting arm so th

2-10 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup2.9 Connect External Exhaust DuctingConnect the existing outside-venting du

Installation and SetupCP2230 Setup Guide 2-11020-100515-04 Rev. 1 (05-2014)or becoming unsafe, an alarm sounds if the duct is obstructed or a fan fail

2-12 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup5. Remove the front lens cap.6. On the TPC, tap Menu > Configuration >

Installation and SetupCP2230 Setup Guide 2-13020-100515-04 Rev. 1 (05-2014)2.11 Install the Optional Anamorphic Lens1. Install the M-MALM according to

2-14 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup6. Install the anode yoke assembly. Use this table to determine the correct

Installation and SetupCP2230 Setup Guide 2-15020-100515-04 Rev. 1 (05-2014)2.14 Connect the Lamp Power Supply (LPS) • You must connect the LPS to the

CP2230SETUP GUIDE020-100515-04

2-16 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup2. Connect Lamp Leads: Fire Hazard! To avoid a fire hazard ensure the high

Installation and SetupCP2230 Setup Guide 2-17020-100515-04 Rev. 1 (05-2014)These connectors are controlled with the power connector breaker. For more

2-18 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Installation and Setup2.15 Connect the cinema projector to an Optional Uninterrupted Power Sup-pl

CP2230 Setup Guide 3-1020-100515-04 Rev. 1 (05-2014)3 Connect Devices to the cinema projectorThis section provides information and procedures for conn

3-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Connect Devices to the cinema projector3.1 Connect a Communication DeviceTo communicate with the c

Connect Devices to the cinema projectorCP2230 Setup Guide 3-3020-100515-04 Rev. 1 (05-2014)3.2 Connect Devices to the SCCI PortThe Simple Contact Clos

3-4 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Connect Devices to the cinema projector3.3 Connect Devices to the GPIO PortThe GPIO port is a 37-p

Connect Devices to the cinema projectorCP2230 Setup Guide 3-5020-100515-04 Rev. 1 (05-2014)If you are wiring your own GPIO cable for use with a server

CP2230 Setup Guide 4-1020-100515-04 Rev. 1 (05-2014)4 Adjust the ImageThis section provides information and procedures for adjusting the cinema projec

NOTICES COPYRIGHT AND TRADEMARKS Copyright ©2014 Christie Digital Systems USA, Inc. All rights reserved.All brand names and product names are tradema

4-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image4.4 Adjust OffsetProject an image with the primary lens. Always adjust offset befo

Adjust the ImageCP2230 Setup Guide 4-3020-100515-04 Rev. 1 (05-2014)3. Adjust the Focus using the focus knob to retract the lens. (Figure 4-2) Watch t

4-4 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image4.7 Adjust Top and Bottom Boresight1. Focus the image at the top edge of the scree

Adjust the ImageCP2230 Setup Guide 4-5020-100515-04 Rev. 1 (05-2014)4.8 Adjust Top and Bottom Boresight with an ILS1. Loosen the Vertical Locking Scre

4-6 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image4.10 Fold Mirror AdjustmentIf a corner or edge of an image is missing, the fold m

Adjust the ImageCP2230 Setup Guide 4-7020-100515-04 Rev. 1 (05-2014)4.11 Calibrate the System Use the TPC to calibrate the image color performance and

4-8 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image4.14.2 Hardware SetupUse an infrared emitter to control gating in active glasses,

Adjust the ImageCP2230 Setup Guide 4-9020-100515-04 Rev. 1 (05-2014)5. Run test patterns to verify the performance of the new 3D channel formats.6. Ru

4-10 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image a. Select Line Interleave in the 3D Sync Input Mode list. b. Select 6:2 in the F

Adjust the ImageCP2230 Setup Guide 4-11020-100515-04 Rev. 1 (05-2014)4. Tap a test pattern.5. Put on a pair of 3D glasses. 6. Look at the on-screen im

4-12 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image Figure 4-12 RGB-12bit-3D Four Quadrant Test PatternFRAME 1 - 100% white field bo

Adjust the ImageCP2230 Setup Guide 4-13020-100515-04 Rev. 1 (05-2014) Figure 4-13 RGB-12bit-3D Half Descending Test PatternFRAME 1 - 100% white field

4-14 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Adjust the Image4.14.9 Verify 3D Cinema Content1. Put on a pair of 3D glasses.2. Play the 3D cont

Adjust the ImageCP2230 Setup Guide 4-15020-100515-04 Rev. 1 (05-2014)Ghosting / Cross-talk1. Tap Menu > Channel Setup.2. Select a 3D channel in the

CP2230 Setup Guide 5-1020-100515-04 Rev. 1 (05-2014)5 OperationThis section provides information and procedures for operating the CP2230 cinema proje

CP2230 Setup Guide 6-1020-100515-04 Rev. 1 (05-2014)6 MaintenanceThis section provides information and procedures for performing cinema projector main

6-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Maintenance6.3 Inspect the Lamp Always disconnect the cinema projector from AC power and wear auth

MaintenanceCP2230 Setup Guide 6-3020-100515-04 Rev. 1 (05-2014)2. Wrap a lens tissue around a swab and soak it in lens cleaning solution. The tissue s

6-4 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Maintenancea. Remove the front lamp duct to reveal the cathode end (-) of the lamp.b. Loosen the s

MaintenanceCP2230 Setup Guide 6-5020-100515-04 Rev. 1 (05-2014)tighten. DO NOT stress the glass in any way. 2) Check leads. Make sure the anode (+) le

6-6 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Maintenancec. Complete the fields in the Add Lamp dialog.d. Tap Save.14. On the TPC, tap and hold

MaintenanceCP2230 Setup Guide 6-7020-100515-04 Rev. 1 (05-2014)1. Release two tabs on the air filter cover and remove.2. Slide the air filter out and

CP2230 Setup Guide 7-1020-100515-04 Rev. 1 (05-2014)7 TroubleshootingThis section provides information and procedures for resolving common cinema proj

7-2 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Troubleshooting7.3 Lamp Suddenly Turns Off•Tap Menu > Advanced Setup > Lamp Power/LiteLOC Se

TroubleshootingCP2230 Setup Guide 7-3020-100515-04 Rev. 1 (05-2014)1. From the Desktop Launcher, Administrator Setup: Communication Configuration menu

7-4 CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Troubleshooting7.14 Display is Not Rectangular• Verify the cinema projector is level and the lens

TroubleshootingCP2230 Setup Guide 7-5020-100515-04 Rev. 1 (05-2014)7.19 The Display is Jittery or Unstable• Verify that the input device is connected

Table of ContentsCP2230 Setup Guide i020-100515-04 Rev. 1 (05-2014)1: Introduction1.1 Labels and Markings ...

Japanph: 81-3-3599-7481South Koreaph: +82 2 702 1601For the most current technical documentation, please visit www.christiedigital.com USA – Cypressp

ii CP2230 Setup Guide020-100515-04 Rev. 1 (05-2014)Table of Contents4.13 Electronic Screen Masking ....

Table of ContentsCP2230 Setup Guide iii020-100515-04 Rev. 1 (05-2014)7.13 Inaccurate Display Colors ............